A2 Tool Steel: Properties and Where to Buy It
MetalNow · November 17, 2026
By the MetalNow Team, with 25 years of experience supplying metal to machine shops and fabricators.
Ask a tool and die maker which steel they'd pick if they could only keep one, and a lot of them will say A2. It's not the hardest tool steel out there, and it's not the toughest. But it does almost everything well, and it's forgiving in the shop.
That balance is why A2 shows up in punches, dies, shear blades, gauges and knives in shops all over the country. It holds an edge, stands up to impact better than high-wear grades and barely moves when you harden it.
Below, we'll cover what A2 is made of, its key properties, how it's heat treated, how it stacks up against D2 and O1, and what to look for when you buy it.
The quick answer
A2 is an air-hardening, cold-work tool steel with about 1% carbon and 5% chromium. It hardens to about 57–62 HRC, holds its size well during heat treatment and offers a good mix of toughness and wear resistance.
Choose A2 for punches, dies, shear blades, gauges and tools that see some impact and need to stay dimensionally accurate.
Choose D2 if wear resistance matters more than toughness.
Choose O1 if you want the easiest steel to machine and heat treat for smaller, simpler tools.
What is A2 tool steel?
A2 is part of the "A" family of tool steels. The A stands for air hardening, which means it hardens by cooling in still air instead of being dunked in oil or water. That gentler cool-down is a big reason A2 holds its shape so well.
Its typical chemistry looks like this:
Carbon: about 1.0%
Chromium: about 5%
Molybdenum: about 1.0%
Manganese: about 0.6–0.85%
Vanadium: about 0.25%
The carbon gives it hardness. The chromium and molybdenum let it harden all the way through in air and add wear resistance. The small amount of vanadium helps keep the grain fine for better toughness.
A2 is a cold-work tool steel, meaning it's built for tools that cut, punch or form material at room temperature, not for hot forging or die casting.
Key properties of A2
Hardness. A2 is sold annealed, at about 200–240 Brinell, so it's soft enough to machine. After heat treating, most shops run it at 57–62 HRC, with 60–62 HRC being the common target for punches and dies.
Toughness. This is where A2 earns its reputation. It handles shock and impact noticeably better than D2, so it's less likely to chip or crack on tools that take a beating.
Wear resistance. A2 sits in the middle. It wears better than O1 but not as well as D2 tool steel. For most general tooling, that's plenty.
Dimensional stability. Because it hardens in air, A2 moves very little during heat treatment. That makes it a favorite for precise parts like gauges, fixtures and close-tolerance dies.
Machinability. In the annealed condition, A2 machines at roughly 70% of a plain 1% carbon steel. It's easier to cut than D2, though not as easy as O1. For more on choosing material for the mill, see our guide to the best metals for CNC machining.
Heat treating A2
A2 is one of the more forgiving tool steels to heat treat. Here's the typical process, based on published data sheets. Always follow the guidance from your heat treater or the mill's data sheet for your specific material.
Preheat in two steps, around 1150–1250°F and then 1350–1450°F, to bring the part up evenly.
Austenitize (harden) at about 1725–1775°F. Soak roughly 30 minutes for the first inch of thickness, plus about 15 minutes for each additional inch.
Cool in still air (or pressurized gas in a vacuum furnace) down to around 150°F. Sections thicker than about 3 inches may need a faster cool to harden fully.
Temper right away, at least twice. Most tooling is tempered between 350°F and 500°F for 58–61 HRC. Hold at least 2 hours, or 1 hour per inch of thickness.
A higher temper gives you a little more toughness and a little less hardness. For example, tempering at about 400°F typically lands around 60–61 HRC, while 1000°F drops it to the mid-50s.
Common uses for A2
A2 is a go-to for tools that need to stay sharp, hold their size and survive some impact:
Punches and blanking dies
Forming, trim and coining dies
Shear blades, slitters and industrial knives
Gauges and precision fixtures
Mold inserts and plastic injection tooling
Chuck jaws, dowel pins and wear parts
Woodworking cutters and custom knife blades
If your tool takes repeated hits, like a punch, or needs to stay dead-on after heat treat, like a gauge, A2 is usually a safe starting point.
A2 vs D2 vs O1
These three are the most common cold-work tool steels, and each one has a sweet spot.
A2 vs D2. D2 has about 12% chromium, so it wins on wear resistance and holds an edge longer in abrasive work like long-run blanking. The tradeoff is toughness: D2 is more brittle and more likely to chip under impact. It's also harder to machine and grind. A2 is the better choice when your tool takes shock or you want an easier steel to work with. For a deeper look, see our A2 vs D2 comparison.
A2 vs O1. O1 is an oil-hardening steel. It's cheaper, machines more easily and is popular for simple tools and knives. But oil quenching causes more distortion, and O1 doesn't wear as well as A2. If accuracy after heat treat matters, A2 is worth the step up.
The short version:
Most wear resistance: D2
Best all-around balance: A2
Easiest and lowest cost: O1
Where to buy A2 tool steel (and what to look for)
You can buy A2 from tool steel distributors, industrial suppliers and online metal suppliers like MetalNow. Wherever you buy it, a few things make a big difference:
Make sure it's annealed. Tool steel is normally sold annealed so you can machine it before heat treat. Confirm that's what you're getting.
Order it cut to size. Tool steel isn't cheap, so paying for full bars you don't need adds up fast. Getting it cut close to your finished size saves money and saw time. Our guide to custom metal cuts explains how it works.
Leave stock for cleanup. Bar stock usually has a thin decarburized skin, a soft outer layer that won't harden properly. Plan to machine or grind it off, or buy oversize or precision-ground stock.
Ask for mill certs. For critical tooling, a mill test report confirms the chemistry and traceability. Here's how to read a mill certificate.
Buy only what you need. For prototypes and one-off tools, a supplier with no minimums keeps you from buying a whole bar for one part.
Get A2 cut to size
A2 earns its spot in so many tool rooms because it does a little of everything well. It's tough enough to take a hit, hard enough to hold an edge and stable enough to come out of heat treat close to size.
At MetalNow, we've spent 25 years helping shops get the right metal. Browse our catalog to price tool steel online, cut to your size and shipped nationwide, with no quotes and no minimums. Not sure if A2 is the right fit for your tool? Reach out to our team and we'll help you figure it out.
[CTA BUTTON: "Order Tool Steel Online" → https://metalnow.com/portal/catalog]